Placa de desenvolvimento ZYNQ7000 XC7Z020 FPGA com conector FMC LPC, Ethernet Gigabit duplo, compatível com HDMI, cartão SD e giroscópio

The main FPGA chip parameters:

• Chip model: Xilinx ZYNQ7000  XC7Z020-2CLG484I.

• Processor model: Dual-core Cortex-A9.

• Processor frequency: 766MHZ.

• DDR3 (PS): 1GB(1024M), 32 bit wide, 1066M data rate.

• Logic units (LC): 85K.

• Lookup table (LUT): 53200.

• DSP unit multiplier: 220.

• Trigger: 106400.

• RAM: 4.9MBit.

• Speed class: -2.

• Device grade: Industrial -40 to 85 degrees C.
  

The XC7Z020 Development board parameters:

1) Power supply: through the special TYPE-C interface for the development board power supply, is 9-12V DC - IN interface.

2) Development board clock: 33.33M (PS), 50M (PL).

3) Ethernet: Gigabit RTL8211E, RGMII interface, one PS, one PL.

4) USB interface: USB2.0, PS terminal TYPE - C interface, support HOST and SLAVE function.

(Note 1: Adaptor can extend HOST, can be connected to HUB)

(Note 2: SLAVE does not support hot-plugging because the interface is designed not to draw power)

5) Debugger: On-board UART + JTAG download, supports ARM and FPGA development.

6) SD Card Slot: SD0 of PS, SD0 can be BOOT . SD card supports up to 32G.

7) SD NAND: SD1 of PS, chip model CSNP1GCR01, 128MByte capacity.

8) HDMI-Compatible Interface: Two PL HDMI-compatible outputs, support up to 1080P.

9) User LEDs and pushbuttons: one pin-button for PS, two pin-buttons for PL. Two PS LEDs, four PL LEDs.

10) Startup setting switch: a B00T dip switch for startup setting .

11) On-board OLED module: 0.96" 128*64 monochrome OLED, SPI interface at PL .

12) Camera Interface: A MIPI CSI 2LANE15PFPC1.0 camera interface.

13) On-board FLASH: 128Mbit(16M bytes).

14) Onboard FMC Interface: The FMC LPC is a standard 34 differential + 2 clock pairs. FMC provides ADJ1 voltage, 3.3V, 9/12V power supply.FMC interface is compatible with ZEDBOARD's FMC pin definition.

15) Supports PYNQ Framework.

16) Expansion IO ports: 34 IO ports, BAN13, providing 5V, 3.3V power supply. Default 3.3V level standard 34 single-ended IOs, all alignments are equal length and consider PIN DELAY.

17) System Reset: A system reset (POR) button.

18) Board Indicators: DONE, USBCPEN, PG and Power Plugged In indication.

19) Board Power System: Input DC to 5V/5A.

On-board kernel power supply: 1.0V/6A.

Remaining circuits: 1.8V/3A, 1.5V/3A, 3.3V/3A.

BANK3435 power supply ADJ1 of FMC: 2.5V/3A by default.

BANK13 power supply ADJ2 of 40P expansion IO port: default 3.3V/3A.

Note 1: All TYPE-C except DC - IN can be powered, the rest of TYPE-C are suspended and have no power supply function.

Note 2: FMC uses BANK3435 as HR BANK, only 2.5V ADJ1 voltage supports LVDS _25 differential standard.

Note 3: 40P uses BANK13 as HR BANK, all are single-ended signals.

The Shipping List:

• 1 * XC7Z020 development board

• 2 * USB cable

• 1 * Power cable