Zenobbq rotisserie cesta rotativa grelha de peixe churrasco cuspir prateleira de carne automática cozimento ajuste de comprimento livre acessórios torrador

DESCRIPTION

Electric Rotisserie is composed of the following parts:
1 Bracket 2 Extension rod 3 Rotating rod 4 Multi-function DC motor 5 Fork(304 stainless steel) with thumb screws(304 stainless steel) 6 Nylon Handle 7 X net
It can be installed on the ovens(BBQ stoves) to automatic rotate roast whole chicken, roast fish, roast vegetables, etc. Quick to install without tools and easy to carry. The length can be adjusted freely within the effective range.

DIMENSION

Supports ovens(BBQ stoves) with inner diameters below 78cm. They all clamping ovens(BBQ stoves) wall thickness are not exceeding 50mm. If you are not sure whether your oven(BBQ stove) is suitable, you can provide a picture of your oven(BBQ stove) inner diameters and wall thickness to the customer service online.

BRACKET

NOTE: The default are V(vertical) brackets.
There are two kinds of brackets: V(vertical) brackets and H(horizontal) brackets and Use V(vertical) brackets by default, If you need H(horizontal) brackets, please contact customer service. All brackets using 2mm thickness stainless steel plates, with three heights, and using thread locking devices.

THREE HEIGHTS

High - Middle - Low

DEFAULT USE THE V(VERTICAL) BRACKET TO INSTALL ON THE OVEN (BBQ STOVE)

NOTE: The oven(BBQ stove) below not included

USE H(HORIZONTAL) BRACKET TO INSTALL ON THE BBQ TABLE (please contact customer service)

NOTE: The BBQ table below not included

MULTI-FUNCTION DC MOTOR（DON'T USE rechargeable battery）

Specifications:
Condition: 100% Brand New
Material: Nylon + Metal
Main Color: White
No Load Current: Below 180MA
Output : 2~5RPM
Rotary Direction: CW
Voltage: DC 5V(With 1 meter USB wire)
Battery: 3pcs AAA batteries (not included, DON’T USE rechargeable battery)
NOTE:DON'T USE rechargeable battery
Rotator Port : 0~5.0kgf.cm(0~11 lbs)
Roast Branch Size: 8 * 8mm / 0.32 * 0.32in
Motor Size: 6.8 * 6.8 *6.5cm / 2.7 * 2.7 * 2.6in

MOTOR INSTALLATION INSTRUCTIONS

STEP1
Press and slide out the Battery Compartment Cover.
STEP2
Put in 3pcs AAA batteries (prepared by customer，DON'T USE rechargeable battery) or connect with a power bank (prepared by customer) use the USB wire.
NOTE:Many power banks on the market have over-current protection functions. When the motor is used, the current passing through increases as the load increases. Once the allowable current is exceeded, the power bank will automatically cut off the power, which will cause the motor to stop, which is not the quality of the motor. For this reason, we recommend using a power bank without over-current protection function.
STEP3
Insert the motor output shaft to the Rotating rod.
STEP4
Option A
If the limit pin is pre-screwed onto the motor, as shown in the figure below, lift the motor slightly and rotate it at an angle to allow the limit pin to slide into the large groove, and then let it fall freely.

Option B
If the limit pin is not screwed on the motor in advance, as shown in the figure below, insert the limit pin and tighten it clockwise to fix it.

INSTALLATION STEPS

Step1
Turn the locking screws on the one bracket counterclockwise to loosen to the appropriate position. Then clamp this bracket to the appropriate position of the oven(BBQ stove) (sold separately, the same below), Turn the locking screw clockwise not to tighten.

Please click on the picture below to purchase the HANDLE

Please click on the picture below to purchase the GRILL COUNTER BALANCE

Please click on the picture below to purchase the FORKS

Please click on the picture below to purchase the ROTATING SKEWERS