RockFlight RFFC F405 V3 flight control module / 60A 4in1 BLheli_S ESC wind power speed controller for RC FPV racing drone
4.214+ sold
£18.99£40.40
53% OFFBuy on AliExpress
You will be redirected to AliExpress to complete your purchase
Specifications
- Brand Name
- AEVYVKV
- Origin
- Mainland China
- High-concerned chemical
- None
- Condition
- New
- Type
- Module
- Choice
- yes
Product Description
Product Name: RFFC-F405 Flight Control
Main control: STM32F405
Gyroscope: ICM42688P
USB interface Type: Type-C
Barometer: Built-in (optional)
OSD chip: AT7456E
WiFI: Not supported
Connection method of DJI Air Unit: Supports direct plug connection method of 6-pin socket
6-pin DJI Sky End Straight socket: Supported. Fully compatible with DJIO3/RunCam Link/Caddx Vista/DJIAir Unit V1 without changing any wire sequence.
Black box: On-board large-capacity Nor flash (optional)
Galvanometer: Supports (Scale=200 Offset=0)
Input voltage: 3S - 6S lithium battery (Power is supplied to the flight control through the G and V wires of the 8-pin ribbon cable on the back of the flight control or the G and V pads on the back of the flight control)
5V BEC output: 9 groups of 5V output (1 front +5V pad + 1 BZ+ buzzer pad, 1 external LED light strip pad), with a total current output of 1.5A
9V BEC output: 3 groups of 9V outputs (1 +9V pad on the front, 2 cells on the back containing +9V outputs), with a total current of 2A
The electronic speed control signal line: The M1-M4 sockets are on the back of the board, and the solder joints are on the front of the board
UART serial ports: 4 groups (UART1< for GPS>, UART3< for receiver >, UART4, UART6)
BetaFlight camera parameter adjustment pad: Supports socket (front CC pad)
Traditional BF LED pads: Supported. The 5V, G, LED pad located at the lower right of the front. It is used to connect the WS2812 LED light strip and is controlled by BF firmware.
Buzzer pad: Supported. Connect the BZ+ and BZ- pads to a 5V passive buzzer
BOOT key: Supported. Press and hold the BOOT button while simultaneously powering the flight control system to force it into DFU mode, which is used for firmware flashing when problems occur with the flight control system.
Supported flight control firmware types: BetaFlight(default factory firmware), INA(INAV firmware can only use Multishot< Recommendation > and OneShot125). Please note that DShot is not supported.
Installation hole position: 30.5 x 30.5mm (4mm hole diameter)
Dimensions: 36.0(length) x 36.0(width) x 7.8(height)mm
BLHeli-S 60A 3-6S DShot600 4-in-1 ESC:
Supports Dshot600, Dshot300, Dshot150, Oneshot125, Multishot, PWM control signal
Voltage: 3-6S (12-26V)
Continuous current: 60A
No built-in 5V BEC output
Main control: STM32F405
Gyroscope: ICM42688P
USB interface Type: Type-C
Barometer: Built-in (optional)
OSD chip: AT7456E
WiFI: Not supported
Connection method of DJI Air Unit: Supports direct plug connection method of 6-pin socket
6-pin DJI Sky End Straight socket: Supported. Fully compatible with DJIO3/RunCam Link/Caddx Vista/DJIAir Unit V1 without changing any wire sequence.
Black box: On-board large-capacity Nor flash (optional)
Galvanometer: Supports (Scale=200 Offset=0)
Input voltage: 3S - 6S lithium battery (Power is supplied to the flight control through the G and V wires of the 8-pin ribbon cable on the back of the flight control or the G and V pads on the back of the flight control)
5V BEC output: 9 groups of 5V output (1 front +5V pad + 1 BZ+ buzzer pad, 1 external LED light strip pad), with a total current output of 1.5A
9V BEC output: 3 groups of 9V outputs (1 +9V pad on the front, 2 cells on the back containing +9V outputs), with a total current of 2A
The electronic speed control signal line: The M1-M4 sockets are on the back of the board, and the solder joints are on the front of the board
UART serial ports: 4 groups (UART1< for GPS>, UART3< for receiver >, UART4, UART6)
BetaFlight camera parameter adjustment pad: Supports socket (front CC pad)
Traditional BF LED pads: Supported. The 5V, G, LED pad located at the lower right of the front. It is used to connect the WS2812 LED light strip and is controlled by BF firmware.
Buzzer pad: Supported. Connect the BZ+ and BZ- pads to a 5V passive buzzer
BOOT key: Supported. Press and hold the BOOT button while simultaneously powering the flight control system to force it into DFU mode, which is used for firmware flashing when problems occur with the flight control system.
Supported flight control firmware types: BetaFlight(default factory firmware), INA(INAV firmware can only use Multishot< Recommendation > and OneShot125). Please note that DShot is not supported.
Installation hole position: 30.5 x 30.5mm (4mm hole diameter)
Dimensions: 36.0(length) x 36.0(width) x 7.8(height)mm
BLHeli-S 60A 3-6S DShot600 4-in-1 ESC:
Supports Dshot600, Dshot300, Dshot150, Oneshot125, Multishot, PWM control signal
Voltage: 3-6S (12-26V)
Continuous current: 60A
No built-in 5V BEC output
Firmware: BLHeli-S
Mounting hole spacing: 30.5*30.5MM
Aperture: 4MM
Weight: 14.6 grams
Mounting hole spacing: 30.5*30.5MM
Aperture: 4MM
Weight: 14.6 grams
There is a filter capacitor on the ESC board, which is used to suppress the back-EMF, stabilize the battery voltage, and protect the precision components of the flight control ESC.
- EMI case provides stronger anti-interference capability.
The RFFC-F405 flight control does not support wireless firmware flashing
Pros & Cons
Pros
- High-performance STM32F405 and ICM42688P gyro
- Integrated 60A ESC for power
- DJI Air Unit compatible
- Built-in OSD and barometer options
Cons
- No WiFi support
- Specific to FPV racing drones
- Assembly required for full setup
- Chinese origin potential firmware issues
Common Questions
What components are in this flight control module?
RFFC F405 V3 with STM32F405 MCU, ICM42688P gyro, includes 60A 4in1 BLheli_S ESC.
What size or compatibility for RC FPV drones?
Designed for RC FPV racing drones, supports DJI Air Unit direct plug via 6-pin socket.
Does it have OSD or barometer features?
Yes, AT7456E OSD chip, built-in barometer (optional), Type-C USB.
How to use this drone flight controller?
Connect ESC, motors, receiver; configure via USB for FPV racing setups.
Shipping origin for this drone module?
Mainland China, new condition module.
Product information last updated on December 21, 2025